Intermittent hot water on tankless heater

Plumbing Forums

Help Support Plumbing Forums:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

bw nc

Member
Joined
Aug 31, 2021
Messages
16
Reaction score
2
Location
NC
We just moved into a house and there is a tankless hot water heater. We are experiencing the hot water disappearing intermittently in the Master Bath shower. The water turns cold for a minute or so and then returns. It only happens at this location. For what it is worth, I checked the shower cartridge and it seems fine.
 
We just moved into a house and there is a tankless hot water heater. We are experiencing the hot water disappearing intermittently in the Master Bath shower. The water turns cold for a minute or so and then returns. It only happens at this location. For what it is worth, I checked the shower cartridge and it seems fine.
FYI Rinnai R75LSi
 
It’s not the water heater if it doesn’t happen at other showers
 
Probably a bad cartridge or balancing spool
Thanks. I had a spare cartridge that I tried and it still went cold. When I look at the unit while the shower is running, I actually see the "in Use" light turn off. Whereas it stays on and functions normally when the other showers are in use.
 
Thanks. I had a spare cartridge that I tried and it still went cold. When I look at the unit while the shower is running, I actually see the "in Use" light turn off. Whereas it stays on and functions normally when the other showers are in use.

i have no idea, goodluck 👍
 
Possibly that particular shower head has such low flow that it's below the minimum for the heater to keep heating? If someone would use hot water at another location that's on the same water heater it might increase the flow enough so the heater stays on. I have some understanding of how tankless water heaters work, and I don't think I ever want one!
 
Minimum activation flow rate .4 GPM

Minimum flow rate .26 gpm

So once it fires off at .4 gpm it can flow a minimum of .26 gpm. That’s a trickle.
 
Possibly that particular shower head has such low flow that it's below the minimum for the heater to keep heating? If someone would use hot water at another location that's on the same water heater it might increase the flow enough so the heater stays on. I have some understanding of how tankless water heaters work, and I don't think I ever want one!
thanks for the inf
 
interesting twist related to flow and pressure. When I turned on the hot water at the sink in the same bathroom and left it running during my shower, the water stayed warm in the shower...
 
interesting twist related to flow and pressure. When I turned on the hot water at the sink in the same bathroom and left it running during my shower, the water stayed warm in the shower...

Turn your water heater temp down some.

What temp is your water ?

Still doesn’t make much sense. .25 a minute minimum flow rate is not much water.......

Brainboard might be bad on that a rinnai. That or you’re not using much hot water when you shower.

No trouble codes ever thrown by the heater ?
 
Turn your water heater temp down some.

What temp is your water ?

Still doesn’t make much sense. .25 a minute minimum flow rate is not much water.......

Brainboard might be bad on that a rinnai. That or you’re not using much hot water when you shower.

No trouble codes ever thrown by the heater ?
temp is set at 120, did not see any error codes
 
temp is set at 120, did not see any error codes

So it doesn’t cut off if you use a lot of hot water, shower and lavatory running.

If nothings wrong with the master shower faucet then I would say the brainboard of the Rinnai may be defective.

I say that because I’d should only take .25gpm per minute to keep the Rinnai firing.

And it’s not throwing a code......

I suppose the flow sensor could be defective but usually it’ll throw a trouble code.

Turn off the cold water to the tankless water heater. Go to the lavatory faucet and open the hot water side only. Verify the hot water flow stops completely. If it doesn’t, that’s a problem.
 
So it doesn’t cut off if you use a lot of hot water, shower and lavatory running.

If nothings wrong with the master shower faucet then I would say the brainboard of the Rinnai may be defective.

I say that because I’d should only take .25gpm per minute to keep the Rinnai firing.

And it’s not throwing a code......

I suppose the flow sensor could be defective but usually it’ll throw a trouble code.

Turn off the cold water to the tankless water heater. Go to the lavatory faucet and open the hot water side only. Verify the hot water flow stops completely. If it doesn’t, that’s a problem.
I'll give it a try later on and let you know. Thanks for the info. Quite a little mystery, it's interesting playing detective, but my wife's not too thrilled when she has shampoo in her hair and it turns cold. :)
 
When it turns cold is there anything you can do to make it come back on.

Like stepping to the side and turning on all hot ?
Turning all the water off in the shower snd then back on ? Try that too
 
Could be a cross-connection issue.

Do you have a second thermostatic valve in the shower?

I've had issue where the hot water flows through the valve fine but after a while, water starts to flow through another thermostatic valve instead and in turn starts pulling water from the cold side into the hot side system not allowing the required amount of flow through the tankless to operate the flow switch. Check the check valves in the thermostatic valve and replace.

If there's a recirculation pump, the water may be backflowing through the line creating a similar scenario above.
 
Could be a cross-connection issue.

Do you have a second thermostatic valve in the shower?

I've had issue where the hot water flows through the valve fine but after a while, water starts to flow through another thermostatic valve instead and in turn starts pulling water from the cold side into the hot side system not allowing the required amount of flow through the tankless to operate the flow switch. Check the check valves in the thermostatic valve and replace.

If there's a recirculation pump, the water may be backflowing through the line creating a similar scenario above.

I agree, I told him how to check for a cross connection. He claims nothings wrong with the shower valve.

The cold flow should also be reduced on a pressure balanced faucet if the hot flow is reduced enough to keep the Rinnai from firing. .25 GPM minimum once it’s up and running.

He claims to have replaced the cartridge. No idea what brand or type.

OP, please post a pic of your shower valve.
 
Had to go out of town. I will take a picture of the cartridge later this week. Thanks.
 
Back
Top