Plumbing Forum - Professional & DIY Plumbing Forum > General Plumbing Discussion > Pumps and Wells > Water pressure issue

Reply
 
Thread Tools Display Modes
Old 08-19-2017, 02:18 AM   #1
Javedisian
Junior Member
 
Join Date: Jul 2017
Posts: 1
Default Water pressure issue

I have a ongoing issue with my water pressure. I have a well. When we do something that uses a lot of water (like using the washer) we lose water pressure to the whole house. If I run the spicket outside we will get some pressure back but then it will go away at times. We had full pressure back at one point but when we did some wash it went back down. What's confusing is the spicket has full pressure and so does the hose hook ups on the house.

We checked the water pressure tank by letting some air out and seeing if any water came out and none came out. The pressure gauge says we are getting 40 psi

Any ideas?

Thank you for reading!


Javedisian is offline  
 
Reply With Quote
Old 08-20-2017, 03:50 PM   #2
Mr_David
Easily Amused
 
Mr_David's Avatar
 
Join Date: Jan 2010
Location: Santee,Ca
Posts: 3,453
Liked 822 Times on 664 Posts
Likes Given: 550

Default

If you have galvanized pipe system there might be a pipe or fitting that has choked off the flow.
Or you have a gate vale that might be broken and only partially opened.

I often see nipple on water heaters choke up with rust scale from electrolysis.
That is easier to evaluate because it only effects all the fixtures in the house on the hot side.

Look for a gate valve between the good flow and the problem area. If the valve stem just turns and turns then the stem is broken in the closed position most likely.


__________________
. . . . . . . . . . -(@@)- . . . . . . . . .
. . . . . ----o00--()--00o----. . . . .

a.k.a. Krazedav
Mr_David is offline  
 
Reply With Quote
Old 08-20-2017, 07:02 PM   #3
speedbump
Wells & pumps; not a...
 
speedbump's Avatar
 
Join Date: Jan 2010
Location: Riverview, Florida
Posts: 1,679
Liked 204 Times on 185 Posts
Likes Given: 46

Default

You don't have any of those in line "Whole house filters" do you?

Does the pump keep up with demand or does the pressure on the gauge go down while your losing pressure at the washer?
speedbump is offline  
 
Reply With Quote
Old 08-22-2017, 02:19 AM   #4
Diehard
Junior Member
 
Join Date: Aug 2017
Location: North reading, Mass.
Posts: 1
Default

As you may already know the flow and pressure available at any point in the system is based on the capabilities of the water source(in your case a pump) and the pressure losses through the piping system.
Without getting into a lot of detail, as your flow demand goes up your pressure losses increases due to increased friction through the piping system and the fact the pump(assuming it's a centrifugal pump) is only capable of a certain pressure at a certain flow.
If your pump is only capable of 40 psi at static (no flow) conditions, you could easily lose a lot of that pressure based on your flow demands and pressure losses through the piping system.
Is this something that was once much better and is now getting worse, which could be caused by one or more of the above suggestions, or was it always relative poor pressure.
To analyze it properly, it should be looked as a system. That is, getting the actual pumps performance curves. That's a curve that shows it's capacity at a specific pressure. Then plotting the piping systems lengths and sizing to the various demands to determine the pressure losses at the various flows. Of course the flows would be limited to the pumps capabilities at a particular flow vs pressure.
It my sound confusing but it's quite simple to estimate what to expect for flow vs pressure at any point in the system once plotted out with all the pipe sizes and lengths, bends, valves and any other device that would contribute to pressure loss and match that against the capabilities of the pump.
Diehard is offline  
 
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Water Pressure Issue Ssmo72 General Plumbing Help 2 05-28-2017 04:17 PM
Water Pump or Pressure Tank issue rumads Pumps and Wells 2 08-04-2016 02:24 PM
high hot water pressure issue cartercargill General Plumbing Help 8 02-06-2016 03:55 AM
Water pressure issue and what next?! sfoxis Pumps and Wells 3 12-26-2015 02:23 PM
Water supply and pressure issue wingnutty General Plumbing Help 9 07-01-2013 02:07 PM



Newest Threads