Plumbing Forum - Professional & DIY Plumbing Forum > Search Forums > Search Results



Showing results 1 to 10 of 10
Search took 0.01 seconds.
Search: Posts Made By: Plumbero007
Forum: General Discussion 05-05-2012, 03:40 PM
Replies: 13
Views: 805
Posted By Plumbero007
I just run google search for: Lake County,...

I just run google search for:
Lake County, Florida plumber
Where are you.....???
For now forget about social marketing, firs fix that gaping hole.
Get a website you can update yourself, dead...
Forum: General Plumbing Help 05-05-2012, 03:07 PM
Replies: 4
Views: 1,249
Posted By Plumbero007
I'm assuming that you got 4" cast iron stub-out...

I'm assuming that you got 4" cast iron stub-out currently flush with concrete slab. Measure distance of top of the rubber gasket to bottom of your toilet flange. if you have 2" there you will be...
Forum: General Plumbing Help 03-31-2012, 01:11 PM
Replies: 6
Views: 1,314
Posted By Plumbero007
Is a kitchen drain vented?. Check the roof ...

Is a kitchen drain vented?. Check the roof above kitchen sink.
If you have window above kitchen sink there should be a vertical vent pipe on ether side of the window. If the sink is vented, run 1...
Forum: General Plumbing Help 03-18-2012, 01:40 AM
Replies: 6
Views: 1,314
Posted By Plumbero007
any pictures?. it would help. Washing machine...

any pictures?. it would help. Washing machine needs its own, separate trap. Where is the vent for all this?
Forum: General Plumbing Help 03-18-2012, 01:36 AM
Replies: 17
Views: 1,253
Posted By Plumbero007
American Standard will do nicely. Looks like you...

American Standard will do nicely. Looks like you have gone dip enough, so you can install whatever mom likes.
Forum: General Plumbing Help 02-25-2012, 05:41 PM
Replies: 2
Views: 446
Posted By Plumbero007
what is your pump well pressure, at start of...

what is your pump well pressure, at start of cycle and end of pumping cycle?. to run 3 heads you will need at list 55 psi
Forum: Water Heaters and Softeners 02-14-2012, 12:49 PM
Replies: 20
Views: 1,833
Posted By Plumbero007
remove Vertical nipple and L-bow. replace L-bow...

remove Vertical nipple and L-bow. replace L-bow with "T" with extra opening pointing down. Screw 4" nipple pointing down and cap it. When you at this increase length of this vertical nipple by about...
Forum: General Plumbing Help 02-13-2012, 11:33 PM
Replies: 3
Views: 553
Posted By Plumbero007
You can drill from inside of the garage at angle,...

You can drill from inside of the garage at angle, so your drill bit comes on outside bellow ground level, dig hole outside to fond end of your bit. Keep in mind that depends on your location section...
Forum: General Plumbing Help 02-13-2012, 12:14 AM
Replies: 16
Views: 918
Posted By Plumbero007
Water meter valve on street side with padlock...

Water meter valve on street side with padlock holes belongs to the city and should be the City's responsibility. As mr_Dave above responded if that valve is not working City should fix it.
After...
Forum: Showers and Tubs 02-06-2012, 02:53 PM
Replies: 6
Views: 2,366
Posted By Plumbero007
Looks like somebody in the past inserted sleeves...

Looks like somebody in the past inserted sleeves before tile job was completed. Use small chisel or old screwdriver to chip mortar around sleeves, then try to unscrew them.
This old faucet should...
Showing results 1 to 10 of 10